What is Network Cabling?

Cable is the medium through which information usually moves from one network device to another. There are several types of cable which are commonly used with LANs. In some cases, a network will utilize only one type of cable, other networks will use a variety of cable types. The type of cable chosen for a network is related to the network's topology, protocol, and size. Understanding the characteristics of different types of cable and how they relate to other aspects of a network is necessary for the development of a successful network.
The following sections discuss the types of cables used in networks and other related topics.

• Unshielded Twisted Pair (UTP) Cable
• Shielded Twisted Pair (STP) Cable
• Coaxial Cable
• Fiber Optic Cable
• Cable Installation Guides
• Wireless LANs
• Unshielded Twisted Pair (UTP) Cable

Unshielded twisted pair

Category	Speed	Use
1	1 Mbps	Voice Only (Telephone Wire)
2	4 Mbps	LocalTalk & Telephone (Rarely used)
3	16 Mbps	10BaseT Ethernet
4	20 Mbps	Token Ring (Rarely used)
5	100 Mbps (2 pair)	100BaseT Ethernet
	1000 Mbps (4 pair)	Gigabit Ethernet
5e	1,000 Mbps	Gigabit Ethernet
6	10,000 Mbps	Gigabit Ethernet

1.Unshielded Twisted Pair Connector

The standard connector for unshielded twisted pair cabling is an RJ-45 connector. This is a plastic connector that looks like a large telephone-style connector (See fig. 2). A slot allows the RJ-45 to be inserted only one way. RJ stands for Registered Jack, implying that the connector follows a standard borrowed from the telephone industry. This standard designates which wire goes with each pin inside the connector.

2.Shielded Twisted Pair (STP) Cable

Although UTP cable is the least expensive cable, it may be susceptible to radio and electrical frequency interference (it should not be too close to electric motors, fluorescent lights, etc.). If you must place cable in environments with lots of potential interference, or if you must place cable in extremely sensitive environments that may be susceptible to the electrical current in the UTP, shielded twisted pair may be the solution. Shielded cables can also help to extend the maximum distance of the cables.

Shielded twisted pair cable is available in three different configurations:

1. Each pair of wires is individually shielded with foil.
2. There is a foil or braid shield inside the jacket covering all wires (as a group).
3. There is a shield around each individual pair, as well as around the entire group of wires (referred to as double shield twisted pair).

3.Coaxial Cable

Coaxial cabling has a single copper conductor at its center. A plastic layer provides insulation between the center conductor and a braided metal shield (See fig. 3). The metal shield helps to block any outside interference from fluorescent lights, motors, and other computers.

4.Coaxial Cable Connectors

The most common type of connector used with coaxial cables is the Bayone-Neill-Concelman (BNC) connector (See fig. 4). Different types of adapters are available for BNC connectors, including a T-connector, barrel connector, and terminator. Connectors on the cable are the weakest points in any network. To help avoid problems with your network, always use the BNC connectors that crimp, rather screw, onto the cable.

5.Fiber Optic Cable

Fiber optic cabling consists of a center glass core surrounded by several layers of protective materials. It transmits light rather than electronic signals eliminating the problem of electrical interference. This makes it ideal for certain environments that contain a large amount of electrical interference. It has also made it the standard for connecting networks between buildings, due to its immunity to the effects of moisture and lighting.

Fiber optic cable

Specification	Cable Type
10BaseT	Unshielded Twisted Pair
10Base2	Thin Coaxial
10Base5	Thick Coaxial
100BaseT	Unshielded Twisted Pair
100BaseFX	Fiber Optic
100BaseBX	Single mode Fiber
100BaseSX	Multimode Fiber
1000BaseT	Unshielded Twisted Pair
1000BaseFX	Fiber Optic
1000BaseBX	Single mode Fiber
1000BaseSX	Multimode Fiber

6.Wireless standards and speeds

The Wi-Fi Alliance is a global, non-profit organization that helps to ensure standards and interoperability for wireless networks, and wireless networks are often referred to as WiFi (Wireless Fidelity). The original Wi-Fi standard (IEEE 802.11) was adopted in 1997. Since then many variations have emerged (and will continue to emerge). Wi-Fi networks use the Ethernet protocol.

Standard	Max Speed	Typical Range
802.11a	54 Mbps	150 feet
802.11b	11 Mbps	300 feet
802.11g	54 Mbps	300 feet
802.11n	100 Mbps	300+ feet